نتایج جستجو برای: آلومینیم 5083
تعداد نتایج: 2112 فیلتر نتایج به سال:
Anais do Congresso Internacional de Engenharia Mecânica e Industrial (2764-4294) - Simulação Numérica Do Impacto Balístico De Um Projétil Ap 7,62 Mm Penetrando Uma Placa Alumínio 5083-H116 Com Diferentes Ângulos E Velocidades
Antoine Roueff, Jérôme I. Mars and Jocelyn Chanussot, Senior Member, IEEE contact information : [email protected] , Institut Fresnel, Groupe Physique et Traitement de l’Image DU Saint Jérôme 13397 Marseille cedex 20, France Tel : +33 (0)4 91 28 80 48, Fax : +33 (0)4 91 28 82 01 [email protected], Laboratoire des Images et des Signaux (LIS) BP 46 38402 Saint Martin d’Hères Cédex Fr...
The influence of nanoscale reinforcement on the mechanical behavior of ultrafine-grained composites was studied. Al 5083 (Al– 4.5 Mg–0.57Mn–0.25Fe) composites, with grain size of 115 nm and B4C reinforcement size of 38 nm, were fabricated via cryomilling and consolidation. The result reveals that the presence of nanoparticles enhances strength by interacting with dislocations, while simultaneou...
In this research, a finite element (FE) technique was used to predict the residual stresses in laser-peened aluminum 5083 at different power densities. A dynamic pressure profile create wave an explicit model, and stress results were extracted once solution stabilized. It is shown that as density increases from 0.5 4 GW/cm2, induced develop monotonically deeper 0.42 1.40 mm. However, with incre...
ریز کردن دانه ها روشی موثر و اقتصادی برای بهبود خواص مکانیکی مواد است. از آنجایی که کاهش اندازه دانه مواد فلزی به زیر mµ 5 با روش های متداول کارسرد و تبلور مجدد عملاً دشوار است، روش هایی جدید نظیر سینتر کردن نانو پودر ها، آلیاژ سازی مکانیکی و کریستاله کردن ساختار های آمورف سریعاً سرد شده برای تولید دانه های فوق ریز (ufg) توسعه یافتند، اما این روشها برای تولید مواد حجیم عاری از نقص با دشواری های ز...
به منظور تولید رادیوایزوتوپ تکنسیم-۹۹ حاصل از واپاشی رادیواکتیو مولیبدن-۹۹ و خالصسازی محصول فرایند انحلال اسیدی هدف مینیاتوری، لازم است آلودگی ید گازی در حد قابل قبولی کاهش یابد. این جاذبهای جامد استفاده میشود. یکی بهترین مورد موردنیت حاوی نقره تشکیل شده است. پژوهش روش سنتز مشخصات جاذب بررسی قرار گرفته برای تهیه بلورهای حفرهدار با اندازه حدود ۱۰ میکرومتر نسبت آلومینیم سیلیکون برابر 2/5 شد ...
The paper deals with the optimization of welding parameters of friction stir welding of different Aluminium alloy groups. For this purpose 5 series Aluminium alloy Al 5083 and 6 series Aluminium alloy Al 6062 were taken .Tensile Strength test and micro structure analysis under various rotating speeds and tool profiles is conducted. It is observed that the increase in tool rotation speed and the...
We conducted an experimental and analytical study to understand the mechanisms and dominant parameters for ogive-nose rods and 7.62mm APM2 bullets that perforate 5083-H116 aluminum armor plates. The 20-mm-diameter, 95-mm-long, ogive-nose, 197g, hard steel rods were launched with a gas gun to striking velocities between 230-370m/s. The 7.62-mm-diameter, 10.7g, APM2 bullet consists of a brass jac...
در مقالة حاضر، تاثیر میزان آلومینیم و متغیرهای عملیات حرارتی آستمپر بر خواص کششی و سختی چدن خاکستری Fe-C-Si-Al بررسی شده است. به منظور بررسی تاثیر میزان آلومینیم، سه آلیاژ حاوی 1، 2 و 4 درصد وزنی آلومینیم تهیه گردید. بر روی نمونههای کشش تهیه شده از این آلیاژها عملیات حرارتی آستمپر اعمال گردید. بدین ترتیب که این نمونهها در دو دمای ?C850 و ?C900 به مدت 120 دقیقه آستنیته شده و در سه دمای آستمپر ...
نمودار تعداد نتایج جستجو در هر سال
با کلیک روی نمودار نتایج را به سال انتشار فیلتر کنید