Development of Precision Injection Molding by Cooling Rate Control Part IV Effect of Cooling Rate on Shrinkage Characteristics of U-shaped Products
نویسندگان
چکیده
منابع مشابه
: the effect of sericin levels (silk glue protein) on rate of in vitro maturation, fertilization and culture of sheep oocytes
هدف از آزمایش اول بررسی اثر سطوح مختلف سریسین [0 (control), 0.1, 0.5, 1.0, 2.5 %] افزوده شده به محیط , ivm بر cumulus cell expansion، بلوغ هسته و توسعه متوالی جنین، در گوسفندان نژاد سنجابی در فصل تولید مثلی می باشد. از سرگیری میوز به وسیله خارج شدن اولین پولار بادی اندازه گیری و هم چنین درصد رسیدن جنین های دو سلولی به مرحله کلیواژ و بلاستوسیت نیز به عنوان نشانه ای از میزان شایستگی توسعه اولیه ج...
effect of oral presentation on development of l2 learners grammar
this experimental study has been conducted to test the effect of oral presentation on the development of l2 learners grammar. but this oral presentation is not merely a deductive instruction of grammatical points, in this presentation two hypotheses of krashen (input and low filter hypotheses), stevicks viewpoints on grammar explanation and correction and widdowsons opinion on limited use of l1...
15 صفحه اولcontrol of the optical properties of nanoparticles by laser fields
در این پایان نامه، درهمتنیدگی بین یک سیستم نقطه کوانتومی دوگانه(مولکول نقطه کوانتومی) و میدان مورد مطالعه قرار گرفته است. از آنتروپی ون نیومن به عنوان ابزاری برای بررسی درهمتنیدگی بین اتم و میدان استفاده شده و تاثیر پارامترهای مختلف، نظیر تونل زنی(که توسط تغییر ولتاژ ایجاد می شود)، شدت میدان و نسبت دو گسیل خودبخودی بر رفتار درجه درهمتنیدگی سیستم بررسی شده اشت.با تغییر هر یک از این پارامترها، در...
15 صفحه اولthe effect of using visual aids on the development of speech act of disagreement among iranian intermediate efl learners
abstract the present study tried to investigate the effect of visual aids (films) on the development of the speech act of disagreement among iranian efl intermediate learners. to this end, the researcher selected 40 homogeneous intermediate learners based on their scores on oxford placement test. .the subjects then divided into control group and experimental group. both classes were tested by ...
Precision Injection Molding PRECISION PROCESS CONTROL OF INJECTION MOLDING
1 INTRODUCTION The technical requirements of precision injection molded components demand a heightened level of process performance, and with corresponding process monitoring and control technologies. To obtain the desired critical to quality attributes (CTQs) of the molded products, the injection molding process must be consciously designed such that the key process variables (KPVs) are observ...
متن کاملذخیره در منابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
ژورنال
عنوان ژورنال: Seikei-Kakou
سال: 2014
ISSN: 0915-4027,1883-7417
DOI: 10.4325/seikeikakou.26.364