Experimental Investigation on the Behavior of AlSiMgMn Alloy Inoculated by Al-5Ti Master Alloy and Fabricated by Die-Casting with Different Mold Wall Thicknesses
نویسندگان
چکیده
منابع مشابه
EFFECTS OF Al-5TI-1B MASTER ALLOY AND HEAT TREATMENT ON THE MICROSTRUCTURE AND DRY SLIDING WEAR BEHAVIOR OF AN Al-12Zn-3Mg-2.5Cu ALLOY
In this study the effect of Al–5Ti–1B grain refiner on the structural characteristics and wear properties of Al–12Zn–3Mg–2.5Cu alloy was investigated. The optimum amount for Ti containing grain refiners was selected as 2 wt.%. T6 heat treatment, (i.e. heating at 460 °C for 1 h before water quenching to room temperature and then aging at 120 °C for 24 h) was applied for all specimens before wear...
متن کاملEffect of Al–5Ti–C Master Alloy on the Microstructure and Mechanical Properties of Hypereutectic Al–20%Si Alloy
Al-5Ti-C master alloy was prepared and used to modify hypereutectic Al-20%Si alloy. The microstructure evolution and mechanical properties of hypereutectic Al-20%Si alloy with Al-5Ti-C master alloy additions (0, 0.4, 0.6, 1.0, 1.6 and 2.0 wt%) were investigated. The results show that, Al-5Ti-C master alloy (0.6 wt%, 10 min) can significantly refine both eutectic and primary Si of hypereutectic ...
متن کاملinvestigation of effective parameters on the rigidity of light composite diaphragms (psscb) by fem
در این رساله با معرفی سقف های psscb متشکل از ترکیب ورق های فولادی ذوزنقه ای و تخته های سیمانی الیافی به عنوان سقف های پیش ساخته (سازگار با سیستم سازه ای قاب های فولادی سبک) به بررسی پارامترهای موثر بر صلبیت سقف، پرداخته می شود. در تحقیق حاضر ابتدا به مدل سازی دو نمونه سقف آزمایش شده، به روش اجزاء محدود با استفاده از نرم افزار تحلیلی abaqus ver 6.10 پرداخته شده است. نمونه های ساخته شده تحت اعما...
EVALUATION OF PRESSURE EFFECT ON HEAT TRANSFER COEFFICIENT AT THE METAL- MOLD INTERFACE FOR CASTING OF A356 AL ALLOY
Abstract: During solidification and casting in metallic molds, the heat flow is controlled by the thermal resistance at the casting-mold interface. Thus heat transfer coefficient at the metal- mold interface has a predominant effect on the rate of heat transfer. In some processes such as low pressure and die-casting, the effect of pressure on molten metal will affect the rate of heat transfer a...
متن کاملThe Effects Of Ageing Temperature On Tensile Properties And Fracture Behavior Of Al-6Si-0.5Mg Alloy Fabricated By Casting And Treated By T6 Heat Treatment
An Aluminum based in-situ alloy reinforced with Mg2Si and Si hard particles produced by casting Al-6Si-0.5Mg alloy. The microstructure, tensile properties and fracture behavior of the alloy were investigated and the results show that the Mg2Si and Si hard particles produced by precipitation hardening have great effects. The homogenized (24hr at 500 o C) and solutionized (2hr at 540 o C) cast al...
متن کاملذخیره در منابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
ژورنال
عنوان ژورنال: International Journal of Engineering Research and Technology
سال: 2020
ISSN: 0974-3154
DOI: 10.37624/ijert/13.7.2020.1764-1774