FLOW BEHAVIOR OF MOLTEN METAL IN ALUMINUM LFC PROCESS
نویسندگان
چکیده مقاله:
The effects of gating system and pattern geometry on the metal flow in the lost foam casting (LFC) process have been investigated using glass covered mold and video recording system. Unlike convectional casting process, the type of the gating system showed little effect on fillability in lost foam, but pattern thickness had large effect on mold filling. The mold filling behavior seems to be controlled by the combined influences of heat and mass transfer. The flow rate increased with increasing pattern thickness.
منابع مشابه
EFFECT OF HIGH TEMPERATURE OXIDATION ON THE CORROSION BEHAVIOR OF ALUMINIZED LOW CARBON STEEL IN MOLTEN ALUMINUM
Hot dip aluminizing was carried out on the low carbon steel rod under optimized conditions. The aluminized samples were further oxidized at 1000̊C in air atmosphere at two different times of 20 and 60 minutes. Microstructure study and phase analysis were studied by scanning electron microscopy and X-ray diffraction methods, respectively. The characterization of the coating showed that, Fe2...
متن کاملHigh-pressure Injection Injury with Molten Aluminum
INTRODUCTION A previously healthy 65-year-old male presented to the emergency department complaining of a burn to his right forearm. Just prior to arrival the patient was working at a tool and die company casting products with molten aluminum where he inadvertently caused his injury. Physical examination revealed a burn to the right forearm of varying degrees of severity. A non-painful charred ...
متن کاملEFFECTS OF ELEVATED TEMPERATURE ON MECHANICAL BEHAVIOR OF AN ALUMINUM METAL MATRIX COMPOSITE
Effects of temperature on properties and behavior of a 20 vol % particulate SiC reinforced 6061 aluminum alloy and 6061 unreinforced Al alloy were investigated. Yield strength and elongation to failure were measured as a function of test temperatures up to 180^oC. In addition, the effects of holding time at 180^ oC on tensile properties and fracture mechanisms of the materials at this temperatu...
متن کاملInvestigation of fluid flow and heat transfer in tube hot metal gas forming process
In this study, hot metal gas forming process of AA6063aluminumtubeis studied with a focus on heat transfer of both fluid and solid phases numerically. An experimental study is simultaneously conducted to validate the numerical method. Some of the most important outputs of the present study, are velocity distribution of fluid inside the tube as well as the fluid in the gap between tube and matri...
متن کاملEFFECT OF A CHLORIDE FLUX ON THE DISSOLUTION OF Mn-Al COMPACTS IN MOLTEN ALUMINUM
Abstract: Dissolution and recovery of Mn-Al compacts with and without a chloride flux was studied by taking samples from the melt after addition of the compact. Events occurring after the addition of the compacts into the melt were studied using water quenched specimens after holding them for a specified time in molten state. The cross sections of these specimens were characterized by SEM a...
متن کاملMechanical and Tribological Behavior of Aluminum Alloy LM13 Reinforced with Titanium Dioxide Metal Matrix Composites
In the present research work physical, mechanical and tribological behavior of Aluminum (Al) alloy LM13 reinforced with Nano-sized Titanium Dioxide (TiO2) particulates were fabricated, mechanical and tribological properties were investigated. The amount of nano TiO2 particulates in the composite was added from 0.5% to 2% in 0.5 weight percent (wt %) increments. The Al-LM13-TiO2 Metal Matrix Com...
متن کاملمنابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
ذخیره در منابع من قبلا به منابع من ذحیره شده{@ msg_add @}
عنوان ژورنال
دوره 1 شماره 2
صفحات 9- 15
تاریخ انتشار 2004-06
با دنبال کردن یک ژورنال هنگامی که شماره جدید این ژورنال منتشر می شود به شما از طریق ایمیل اطلاع داده می شود.
کلمات کلیدی برای این مقاله ارائه نشده است
میزبانی شده توسط پلتفرم ابری doprax.com
copyright © 2015-2023