Load Test and Model Calibration of a Horizontally Curved Steel Box-Girder Bridge

نویسندگان

  • Freydoon Rezaie Assitant Professor, Department of Civil Engineering, Bu-Ali Sina University, Hamedan, Iran.
  • Gona Ahmadi M.Sc., Department of Civil Engineering, Bu-Ali Sina University, Hamedan, Iran.
چکیده مقاله:

In this paper, full scale load test of a horizontally curved steel box-girder bridge is carried out in order to detect structural defects, which reportedly result in unwanted vibrations in nearby buildings. The bridge is tested under the passage of six heavy vehicles at different speeds, so as to determine its static and dynamic responses. A total number of one hundred and two (102) sensors are used to measure the displacements, strains, and accelerations of different points of the bridge. It is observed that the bridge vibrates at a fundamental frequency of 2.6 Hz intensively and the first mode of vibration is torsional instead of flexural. The dominant frequency of vibration of the nearby buildings is computed to be approximately 2.5Hz using rational formulas. Thus, nearness of the fundamental frequency of the bridge to those of the adjacent buildings may be causing resonance phenomenon. However, in static load tests, low ranges of strain and displacement illustrated adequate structural capacity and appropriate safety under static loads. Numerical models are created using ANSYS and SAP2000 software products, so as to design the loading test and calibrate the finite element models. The connections of the transversal elements to the girders, transversal element spacing, and changes of the stiffness values of the slabs were found to be the most influential issues in the finite elements calibration process. Finally, considering the total damage of all members, the final health score of the bridge was evaluated as 89% indicating that the bridge is in a very good situation.

برای دانلود باید عضویت طلایی داشته باشید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

load test and model calibration of a horizontally curved steel box-girder bridge

in this paper, full scale load test of a horizontally curved steel box-girder bridge is carried out in order to detect structural defects, which reportedly result in unwanted vibrations in nearby buildings. the bridge is tested under the passage of six heavy vehicles at different speeds, so as to determine its static and dynamic responses. a total number of one hundred and two (102) sensors are...

متن کامل

Analytical and field investigation of horizontally curved girder bridges

................................................................................................................................... xi Acknowledgements ................................................................................................................. xii Chapter 1 General Introduction ...................................................................................................

متن کامل

Drying and Cracking Effects in Box-girder Bridge Segment

This paper deals with the effect of drying as a moisture diffusion process in a segment of a typical box-girder bridge. Pore relative humidity distributions throughout the cross sections of the plates of the girder are calculated from the diffusion equation, taking its nonlinearity and aging into account. The effect of creep with aging on the stresses produced by drying shrinkage is taken into ...

متن کامل

Structural Reliability Analysis of Corroded Steel Girder Bridge

The natural aging, environmental impact, and appropriate design are certainly playing a serious role in safety of the bridges function. The functional safety of bridge constitutes a prime element of the transportation system serving commuters, passengers and freight. According to Federal Highway Administration, the steel bridges share represents a large amount of the United States' bridges. In ...

متن کامل

Aerodynamic Admittance Research on Wide-body Flat Steel Box Girder

Abstract: Aerodynamic admittance is a key parameter affecting the analysis accuracy of the bridge buffeting response. However, few articles have covered the issue of the wide-body flat box girder with much smaller depth-width ratio (such as 1/12 studied in this paper). Therefore, to explore the real buffeting force of the wide-body flat box girder, experiments of the static force coefficients a...

متن کامل

Ultimate Load Capacity and Behavior of Thin-Walled Curved-Steel Square Struts, Subjected to Compressive Load

There have been some experimental tests on hollow curved-steel struts with thin-walled square sections, in order to investigate their general behavior, particularly their capacity for bearing differing loads. One set of square tubes are cold-formed into segments of circular arcs with curvature radii, equal to 4000 mm. Different lengths of curved struts are fabricated so as to cover a practical ...

متن کامل

منابع من

با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

ذخیره در منابع من قبلا به منابع من ذحیره شده

{@ msg_add @}


عنوان ژورنال

دوره 48  شماره 2

صفحات  305- 322

تاریخ انتشار 2015-12-01

با دنبال کردن یک ژورنال هنگامی که شماره جدید این ژورنال منتشر می شود به شما از طریق ایمیل اطلاع داده می شود.

میزبانی شده توسط پلتفرم ابری doprax.com

copyright © 2015-2023