Thermal Analysis of Turbocharger Steel Gasket via Experimental Test

نویسندگان

چکیده مقاله:

Increasing the power (torque) of nowadays engines, along with reduction of fuel consumption and dimensions of them, cause to the use of turbocharged systems. Since turbo chargers are exposed to the exhaust hot gases and have a high operating speed, it is necessary to utilize high technology design and special materials with high cost. The temperature of the exhaust system with gasoline fuel sometimes reaches 950 degrees Celsius, and the change of operating points causes to its thermal fatigue. Hence, the thermal evaluation is one of the basic design activity for manufacturing and testing of turbo charger and its related parts, such as the turbo gasket. In this paper, a new method for evaluating the temperature of a gasket of a four-cylinder gasoline engine is presented. In this method, the temperature of the closest points to gasket is measured at the turbo housing and the exhaust manifold flange, and finally the temperature of the gasket is estimated using them. The results show that in this study, the maximum temperature of the gaskets is about 807 degrees Celsius, which is consistent with the results of analyzes and other turbo charger temperature measurements. Since the access to turbo charger gasket and direct measurements of its temperature is difficult or impossible, the proposed method can be useful in evaluating the temperature of the turbo charger gasket. Then, the measured temperature in the test of durability of thermal-mechanical fatigue was used and the obtained result was evaluated. The failure of gasket in this type of test could indicate the accuracy of the temperature.   

برای دانلود باید عضویت طلایی داشته باشید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Turbocharger Design and Performance Analysis

Performance testing identifies many aspects of turbocharger performance. Although, when performance is less than satisfactory, test cell mapping only identifies secondary or tertiary troubles demonstrating inconsistencies with expected performance. Such tasks as seeking out and eliminating efficiency losses or increasing operational surge margin are unrealistic expectations when basing your con...

متن کامل

Heat Transfer Analysis in a Turbocharger Turbine: an Experimental and Computational Evaluation

This paper presents the performance of a turbocharger under non-adiabatic conditions in order to assess the impact of heat transfer. A commercial turbocharger was installed on a 2.0 liter diesel engine and measurements were conducted for a range of engine speeds and loads. The test results enabled to assess the impact of the engine on the temperature distribution of the bodies constituting the ...

متن کامل

Thermal and Phase Transformations Analysis in a Premomet® Steel

M. Torres-Lopez, L. Guerra-Fuentes, L. Y. Gomez-Zamorano, M. A. L. Hernandez-Rodriguez, E. Garcia-Sanchez. University Autonomous of Nuevo Leon. Thermal analysis in a PREMOMET® steel has been performed by differential scanning calorimetry (DSC) and highresolution dilatometry. The phase transformation temperatures (Ac1, Ac3, Ms and Mf) of this steel were obtained by the two methods at different h...

متن کامل

Experimental study of the effects of repetitive surge condition on turbocharger performance

When the mass flow rate through the compressor is reduced at a constant pressure ratio, mass flow rate will drop to an extent that the complete reversal of flow and surge occurs. Recently many research focuses on turbocharger surge, however, there are not enough investigation on the effect of surge on the performance of the turbocharger. The aim of the paper is to investigate the effect of repe...

متن کامل

Thermal Analysis of Tire

One of the great enemies of rubber compounds is heat. Heat will cause chemical and physical degradation of vulcanized rubber as well as a considerable loss in its strength. A major source of heat generation in a tire is due to internal friction resulting from the viscoelastic deformation of the tire as it rolls along the road. Another source of heat generation in a tire is due to its contact fr...

متن کامل

Solidification and thermal performance analysis of the low carbon steel during the continuous casting process

The present paper evaluates the effect of the nozzle characteristics on the heat transfer and phase change of the low carbon steel during the continuous casting process. A three-dimensional energy equation and a solidification model are used to drive the governing equation of the phase change and temperature distribution. A linear relation is obtained to predict the temperature-dependent of the...

متن کامل

منابع من

با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

ذخیره در منابع من قبلا به منابع من ذحیره شده

{@ msg_add @}


عنوان ژورنال

دوره 53  شماره 53

صفحات  33- 44

تاریخ انتشار 2019-01

با دنبال کردن یک ژورنال هنگامی که شماره جدید این ژورنال منتشر می شود به شما از طریق ایمیل اطلاع داده می شود.

کلمات کلیدی

کلمات کلیدی برای این مقاله ارائه نشده است

میزبانی شده توسط پلتفرم ابری doprax.com

copyright © 2015-2023