نتایج جستجو برای: tool deflection

تعداد نتایج: 371850  

2016
Paul Kwiat John C. Howell Paul G. Kwiat Kevin Lyons Justin Dressel Andrew N. Jordan

Power-Recycled Weak-Value-Based Metrology Report Title We improve the precision of the interferometric weak-value-based beam deflection measurement by introducing a power recycling mirror, creating a resonant cavity. This results in all the light exiting to the detector with a large deflection, thus eliminating the inefficiency of the rare postselection. The signal-tonoise ratio of the deflecti...

Journal: :IEEE Trans. Communications 1992
Albert G. Greenberg Bruce E. Hajek

An approximate analysis of the transient and steady state behavior of deflection routing in hypercube networks is presented, under a uniform traffic model. In deflection routing congestion causes packets admitted to the network to be temporarily misrouted rather than buffered or dropped. Our approximations show that deflection routing performs remarkably well in hypercube networks, for small as...

2010
V. Guidi W. Scandale A. Vomiero S. Baricordi P. Dalpiaz M. Fiorini A. Mazzolari G. Della Mea R. Milan G. Ambrosi B. Bertucci W. J. Burger P. Zuccon G. Cavoto C. Luci R. Santacesaria P. Valente E. Vallazza A. G. Afonin Y. A. Chesnokov V. A. Maisheev I. A. Yazynin A. D. Kovalenko A. M. Taratin A. S. Denisov Y. A. Gavrikov Y. M. Ivanov L. P. Lapina L. G. Malyarenko V. V. Skorobogatov V. M. Suvorov S. A. Vavilov D. Bolognini S. Hasan A. Mozzanica M. Prest

Deflection of protons under axial channeling in a silicon crystal bent along the <111> axis was observed on experiment with 400-GeV protons at the CERN Super Proton Synchrotron. The deflection efficiency due to axial channeling of protons for the crystal with the bend angle 50 μrad was about 30 %. Axial channeling deflection occurred by means of doughnut scattering and hyper-channeling, this la...

Journal: :journal of computational & applied research in mechanical engineering (jcarme) 2012
aminreza noghrehabadia mohammad ghalambaza afshin ghanbarzadeh

in this paper, a monotone positive solution is studied for buckling of a distributed model of multi walled carbon nanotube (mwcnt) cantilevers in the vicinity of thin and thick graphite sheets subject to intermolecular forces. in the modeling of intermolecular forces, van der waals forces are taken into account. a hybrid nano-scale continuum model based on lennard–jones potential is applied to ...

An experimental study was performed to investigate the effects of the body angle of attack on the tail surface pressure distribution for a half body-tail combination in subsonic flow. The results show, in small deflection angle regions, that the tail deflection has the same effect on the surface pressure as the body angle of attack. However at moderate to high deflections, the flowfiled caused ...

In present study, a mathematical model of the vehicle–floating slab track (FST) interaction is established to investigate the coupled behaviour of vehicle–track system. The FST is modelled as the double Euler -Bernoulli beam including the rail and slab. The railway vehicle is simplified as a multi-rigid-body model. The wheel–rail interface is treated using a nonlinear Hertzian contact model, co...

2014
Uroš ŽUPERL

Primljeno (Received): 2011-10-10 Prihvaćeno (Accepted): 2012-01-22 Original scientific paper The aim of this paper is to present a tool condition monitoring (TCM) system that can detect tool breakage in real time using a combination of a neural decision system, an ANFIS tool wear estimator and a machining error compensation module. The principal presumption was that the force signals contain th...

2013
Z. Karim S. Abdullah

Cutting tool wear is found to be the major cause affecting the finished product in term of surface finish quality, dimensional precision and the cost of the defect. This paper proposes the development of a reliable machine condition monitoring system by using a low-cost piezoelectric sensor to monitor the flank wear progression on the cutting tool. The wear of the cutting insert was measured an...

2007
Joanna C.K. Lai Waleed H. Abdulla Stephan Hussmann

This report describes the development of a prototype system that is capable of monitoring the deflection of a bandsaw blade during wood sawing process. The deflection is caused by tension loss of the saw blade and leads to downgrading and value loss of timbers. A CCD-type laser triangulation sensor has been proposed to monitor the saw blade deflection. Deflection monitoring has to be done in re...

Journal: :Brazilian oral research 2011
Eduardo Uggeri Rodrigues Hiroshi Maruo Odilon Guariza Filho Orlando Tanaka Elisa Souza Camargo

This study evaluated the mechanical performance of teardrop-shaped loops and teardrop-shaped loops with helix used in orthodontic space closure. Sixty retraction loops made with 0.019" x 0.025" stainless steel (SS) and beta-titanium (BT) wires were used. They were attached to a testing machine to measure the magnitudes of the sagittal force and the load-deflection ratio necessary for 1 mm, 2 mm...

نمودار تعداد نتایج جستجو در هر سال

با کلیک روی نمودار نتایج را به سال انتشار فیلتر کنید