An Optimization on the DIN1.2080 Alloy in the Electrical Discharge Machining Process Using ANN and GA

نویسندگان

  • Amin Kolahdooz Young Researchers and Elite Club, Khomeinishahr Branch, Islamic Azad University, Isfahan, Iran
  • Masoud Azimi Department of Mechanical Engineering, Khomeinishahr Branch, Islamic Azad University, Isfahan, Iran
  • Seyyed Ali Eftekhari Young Researchers and Elite Club, Khomeinishahr Branch, Islamic Azad University, Isfahan, Iran
چکیده مقاله:

Electrical Discharge Machining (EDM) process is one of the most widely used methods for machining. This method is used to form parts that conduct electricity. This method of machining has used for hard materials and therefore selects the correct values of parameters which are so effective on the quality machining of parts. Reaching to optimum condition of the DIN1.2080 alloy (D3) machining is very important due to the rapid and widespread use of different industry such as Molding, lathe tools reamer, broaching, cutting guillotine and etc. Therefore the purpose of this study is to consider the effect of the inlet parameters such as current, voltage, pulse on time and pulse off time on the machining chip rate and optimize the inlet parameters for D3 alloy. So to reach better result after doing some experiments to predict and optimize the rate of removing chip, neural network method and genetic algorithm are used. Then optimizing input parameters to maximize the rate of removing chip are performed. In this condition by decreasing time, the product cost is decreased. In this condition, the optimum parameters are obtained under the current of 20 (A), 160 (V), pulse on time of 100 (ms) and pulse off time of12 (ms). At this condition, the rate of machining chip is obtained 0.063 (cm3/min). Also, surveying the level of error and its accuracy are evaluated. According to the obtained error value that is about 5.18%, the used method is evaluated suitable for genetic algorithm.

برای دانلود باید عضویت طلایی داشته باشید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Optimization of Material Removal Rate in Electrical Discharge Machining Alloy on DIN1.2080 with the Neural Network and Genetic Algorithm

Electrical discharge machining process is one of the most Applicable methods in Non-traditional machining for Machining chip in Conduct electricity Piece that reaching to the Pieces that have good quality and high rate of machining chip is very important. Due to the rapid and widespread use of alloy DIN1.2080 in different industry such as Molding, lathe tools, reamer, broaching, cutting guillot...

متن کامل

The Effect of Electrical Discharge Machining Parameters on Alloy DIN 1.2080 Using the Taguchi Method and Optimal Determinant

Electrical discharge machining process, is one of the most widely used methods for machining, the electrically conductive parts. In this way the tool is not in contact with the workpiece and the hardness of workpiece does not affect the machining speed. In Electrical Discharge Machining process, selection of the correct machining parameters are effective in final cost and the quality of the pro...

متن کامل

Optimization of Machining Parametric Study on Electrical Discharge Machining

Abstract—Productivity and quality are two important aspects that have become great concerns in today’s competitive global market. Every production/manufacturing unit mainly focuses on these areas in relation to the process, as well as the product developed. The electrical discharge machining (EDM) process, even now it is an experience process, wherein the selected parameters are still often far...

متن کامل

Optimization of machining parameters and wire vibration in wire electrical discharge machining process

Background: Wire Electrical discharge machining (WEDM) has higher capability for cutting complex shapes with high precision for very hard materials without using high cost of cutting tools. During the WEDM process, the wire behaves like a metal string, straightened by two axial pulling forces and deformed laterally by a sum of forces from the discharge process. Major forces acting on the wire c...

متن کامل

Fuzzy Modeling for Electrical Discharge Machining of Aluminum Alloy

Electrical discharge machining (EDM) is widely used process in the production of mould / dies, aerospace, automobile and electronics industries where intricate complex shapes need to be machined in very hard materials. The selection of the AISI 64430 was made taking into account its wide range of applications in the industrial field: defense, pharmaceutical, aerospace, shipbuilding industries e...

متن کامل

منابع من

با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

ذخیره در منابع من قبلا به منابع من ذحیره شده

{@ msg_add @}


عنوان ژورنال

دوره 6  شماره 1

صفحات  33- 47

تاریخ انتشار 2017-02-01

با دنبال کردن یک ژورنال هنگامی که شماره جدید این ژورنال منتشر می شود به شما از طریق ایمیل اطلاع داده می شود.

میزبانی شده توسط پلتفرم ابری doprax.com

copyright © 2015-2023