نتایج جستجو برای: a356

تعداد نتایج: 456  

2013
M. Ishak A. Amir A. Hadi

Over the years, aluminum content in a vehicle part is increasing due to the needs to reduce weight as well as increase fuel efficiency. Most of the cast product in a vehicle part is mostly cast from A356 alloy. It is used because A356 alloy posses’excellent characteristics over other type of alloy such as cast ability, high weight-to-strength ratio, good corrosion resistance and good weld-abili...

2008
H. Möller G. Govender

The heat treatment cycles that are currently applied to semi-solid processed components are mostly those that are in use for dendritic casting alloys. These heat treatments are not necessarily the optimum treatments. It is shown that a decrease of the solution treatment time at 540 o C from 6 hours to 1 hour does not alter the T4 or T6 tensile properties of the SSM processed A356 alloy. Slightl...

2017
M. Abdulwahab R.M. Dodo I.Y. Suleiman A.I. Gebi I. Umar

The present study examined wear characteristics of A356/melon shell ash particulate composites. Dry-sliding the stainless steel ball against specimen disc revealed the abrasive wear behavior of the composites under loads of 2 and 5N. The composite showed lower wear rate of 2.182 × 10-4 mm3/Nm at 20 wt% reinforced material under load of 5N. Results showed that wear rate decreased significantly w...

2015
Konstantin Borodianskiy Vadim Selivorstov Yuri Dotsenko Michael Zinigrad Hugo F. Lopez

In recent years, improving the mechanical properties of metals has become the main challenge in the modern materials and metallurgical industry. An alloying process is usually used to achieve advanced performance of metals. This paper, however, describes an alternative approach. Modification with ceramic nanoparticles, gas-dynamic treatment (GDT) and a combined treatment were investigated on a ...

2008
H. Möller G. Govender

A solution treatment of 1 hour at 540 o C provided the best results for rheocast alloy A356-T6. Natural aging has a significant influence on the subsequent artificial aging response of the alloy. Arrhenius-type equations were derived to predict the time-to-peak hardness as a function of artificial aging temperature.

ژورنال: :مهندسی متالورژی 2014
محمد حسین میرباقری حامد والی حسن سلطانی

هدف از پژوهش حاضر  ابتدا ارایه دانش فنی ساخت فوم آلیاژی پایه آلومینیم است. به این منظور  فوم a356 تهیه شد و سپس مذاب a356 با 4 درصد مس آلیاژ سازی شد و سپس توسط عامل حباب زای tih2 فوم فلز مذکور تهیه شد. وجود 4-5 درصد مس در آلیاژ a356 می تواند آن را مستعد به عملیات پیرسازی نماید. لذا سیکل عملیات پیرسازی برای فوم مذکور انجام گرفت و ساختار سلولی دو فوم و همچنین خواص مکانیکی آنها مورد مقایسه قرار گر...

ژورنال: :مهندسی متالورژی 0
محمد حسین میرباقری دانشیار گروه مهندسی متالورژی، دانشگاه صنعتی امیرکبیر حامد والی کارشناس مهندسی متالورژی، دانشگاه صنعتی امیرکبیر حسن سلطانی کارشناس مهندسی متالورژی، دانشگاه صنعتی امیرکبیر

هدف از پژوهش حاضر  ابتدا ارایه دانش فنی ساخت فوم آلیاژی پایه آلومینیم است. به این منظور  فوم a356 تهیه شد و سپس مذاب a356 با 4 درصد مس آلیاژ سازی شد و سپس توسط عامل حباب زای tih2 فوم فلز مذکور تهیه شد. وجود 4-5 درصد مس در آلیاژ a356 می تواند آن را مستعد به عملیات پیرسازی نماید. لذا سیکل عملیات پیرسازی برای فوم مذکور انجام گرفت و ساختار سلولی دو فوم و همچنین خواص مکانیکی آنها مورد مقایسه قرار گر...

1998
J. F. Major

Much work has been done, in recent years, to characterize the factors that cause porosity in aluminum castings, and to analyze the impact of porosity or microstructural parameters on fatigue life. What has yet to be done is systematically separate out the effects of dendrite arm spacing and largest pore size from each other, and from the underlying chemical and process parameters that influence...

2013
Satya S. Shivkumar S. Wang C. Keller S. Shivkumar

The Charpy impact energy of A356 alloys has been measured. Instrumented Charpy impact tests have been conducted at 25, 100, 150, and 200 ~ The Charpy specimens were machined from plate castings or tapered cylindrical castings. The plates were produced in sand molds, and tapered cylinders were produced in water-cooled copper molds. Both unmodified and strontium-modified castings were tested. The...

Journal: :Applied sciences 2023

A series of calculations has been conducted to study the high-speed interaction space debris (SD) particles with screens finite thickness. For first time, taking into account fracture effects, a numerical solution obtained for problem high-velocity between SD and volumetrically reinforced penetrating composite screen. The were performed using REACTOR 3D software package in three-dimensional set...

نمودار تعداد نتایج جستجو در هر سال

با کلیک روی نمودار نتایج را به سال انتشار فیلتر کنید